All the tools you need in the house explained


Repairing Fences

A fence is used to protect your home andrail individually. Then tighten both the ends
other private property from intruders andof  the  rails  together.
stray animals. Although a fence is similar to
a wall except its construction (a wall isTo fit a rail in between each pair of post,
usually built for same purpose and is made upmeasure and cut 2X4 bottom rail. Fit the
of concrete materials like bricks, stones), arails flat between the posts. They should be
fence is made up of light materials likeslightly 12 inches up from grade level. The
wood, metal, wires etc. Among these variousbottom rails should be nailed into a place
types of fences, wood fences are mostwith 10d galvanized nail at angle through the
defenseless. For example, a heavy rain, heatpost of fence. To keep rails even use a
blow, wind, snow, can cause wood decay, youlevel.
need to often repair fencing. And for these
types of occasions, you may need help. SoMeasure and cut the fence boards of uniform
here  you  go...length and their distance should be equal
from the bottom of the bottom rail to the top
Basic  Methods  of  Repairing  Fencesof  the  top  nail.
According to your budget, you can purchaseFence  Screening  Repair
timber wood to repair fencing. Timber is more
resistant than any other wood and it isIt's very easy and time saving job to replace
especially useful for underground fencing. Asbroken or rotted screening. The length and
timber wood is costly, you may prefer towidth of new piece you want to fit in place
choose  redwood  or  cedar  as  alternatives.of the old should measure the same as per
entire  piece  that icnludes the bad section.
You can preserve fencing above ground level
by applying paint to it. Note that woodWhile replacing pickets, use cut board
fences are mainly destructed by rot, too.against broken pickets. Draw the top onto a
Hence frequent use of water destroys undernew  board.
ground  fencing.
Hammer out broken pieces and take away them
Fence  Rails  Repairfrom  rails.
Â- Before repairing, you have to saturateFit new picket against the rails and align
damaged areas and 2x4s freely by using woodit.
preservatives. This helps to prevent
spreading  of  rot.Paint  new  one  as  per  old  one.
Â- You have to give a support the railFence  Post  Repair
with a cleat. First the rail should be at
level. Then a 2x4 should be fittedPressure treated cedar, lumber should be
comfortably  under  the  ground.used.  A  long  pair  of  2X4s  is  needed.
Â- Neatly seal the seams at the top andCut one end of 2X4, and fit it into the
sides  of  the  wood.ground  with  opposite  sides  of  post.
Â- T-braces are more useful to repairThrough each 2X4s and the post, pierce two
wood fences. After leveling the rail, pierceholes. Then attach together with galvanized
point  holes  into  the  rail  and  the post.bolts.
Â- Fit the T-braces into the rail usingLikewise, fence gates can be repaired. If
galvanized  screws.  Seal  the  joint.your gate becomes loose or not closing
properly, you need to check the hinges first.
Â- Apply paint of your choice to theIf they are loose, broken, replace them with
T-braces.heavier one. Do proper checking frequently
whether  screws  are  loose  or  broken.
Fence  Sections  Repair
Repairing of fences is easy, fast, and often
After cutting 2X4 rails, measure and cut eachcost-saving work. Give it a try!



1 A B C D 69 70 71 72 73 74 75 76 77 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120